Pelco Stereo System ICISA6500 User Manual

ICISA6500  
Inter-Check® Interface Cable  
Installation/Operation Manual  
C1053M (7/98)  
1.0 WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be  
observed.  
1. Installation and servicing should only be done by qualified service personnel  
and conform to all local codes.  
2. Only use replacement parts recommended by Pelco.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of elec-  
tric shock is present within this unit.  
This symbol indicates that there are important operating and mainte-  
nance instructions in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this  
manual prior to installation and operation.  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120  
 
9. Program register Com Port 1 or 2, according to the following instructions, to  
enable the selected Com Port and send journal printer data to the Inter-Check®.  
Programming Com 1  
a. Turn the register key to P.  
b. Press 60 and Subtotal.  
c. Press 50, X/Time, 2 and Subtotal.  
d. Press 51, X/Time, 0 and Subtotal.  
e. Press 52, X/Time, 0 and Subtotal.  
f.  
Press 53, X/Time, 8 and Subtotal.  
g. Finish programming by pressing Cash.  
h. Turn key back to Reg to run transactions.  
Programming Com 2  
a. Turn the register key to P.  
b. Press 60 and Subtotal.  
c. Press 60, X/Time, 2 and Subtotal.  
d. Press 61, X/Time, 0 and Subtotal.  
e. Press 62, X/Time, 0 and Subtotal.  
f.  
Press 63, X/Time, 8 and Subtotal.  
g. Finish programming by pressing Cash.  
h. Turn key back to Reg to run transactions.  
10. Finally, run a transaction on the register. The transaction should appear on  
your security monitor exactly as it is printed on the printer journal.  
4.0 SPECIFICATIONS  
GENERAL  
Environment:  
Indoor  
Operating Temperature: 32° to 120°F (0° to 49°C)  
Weight:  
Unit  
Shipping  
1.0 lb (0.45 kg)  
2.0 lb (0.91 kg)  
Connectors:  
Two DB-9 connectors  
One RJ-14 connector  
(Design and product specifications subject to change without notice.)  
SA  
MSU  
NG  
COM PORT 2  
COM PORT 1  
Figure 1. Samsung 6500 Com Ports  
Pelco Manual C1053M (7/98)  
3
 
5.0 WARRANTY AND  
RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,  
CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-  
year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications  
(that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.  
AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs  
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under  
this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the  
specific use or application made of the Products. Pelco’s liability for any claim, whether based on  
breach of contract, negligence, infringement of any rights of any party or product liability, relating  
totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent  
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss  
of profit and claims of third parties) however caused, whether by the negligence of Pelco or  
otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981  
to obtain a Repair Authorization number (RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty  
conditions stated above, please include a written explanation with the product when returned.  
Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived  
by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)  
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,  
and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number  
and freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco, the Pelco logo, Camclosure, Esprit,  
Genex, Legacy, and Spectra are registered  
trademarks of Pelco.  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Endura and ExSite are trademarks of Pelco.  
© Copyright 1998, Pelco. All rights reserved.  
4
Pelco Manual C1053M (7/98)  
 

Philips Baby Monitor SBC SC 360 User Manual
Philips Battery Charger R03B4A90 User Manual
Philips Headphones SHU2000 User Manual
Planet Technology Printer FPS 1010M User Manual
Polaroid Digital Photo Frame IDF 0720 User Manual
Polaroid DVD Player PDV 0701A User Manual
Powerline Home Gym P2X User Manual
Precisionaire Air Cleaner PB1209 User Manual
ProForm Treadmill 307770 User Manual
ProForm Treadmill 831293041 User Manual